Scalliwag Posted November 26, 2007 Author Share Posted November 26, 2007 QUOTE (Johnny_D @ Nov 26 2007, 07:42 AM) <{POST_SNAPBACK}>QUOTE (Scalliwag @ Nov 26 2007, 01:26 PM) <{POST_SNAPBACK}>it is great to see you guys too It/s been a long while. Hopefully everybody is still healthy wealthy and wise? lol, Healthy yes. But getting poorer and more stupid by the day i suspect JDHaha! Well one out of three is not a complete loss Link to comment Share on other sites More sharing options...
gaia.plateau Posted November 26, 2007 Share Posted November 26, 2007 Paging MNHookah...Paging MNHookah...As the self-appointed representative of this community, I hubmly request that make a version of the glass scalli mod with a glass screen on it... and we'll give you lots of $$$ Link to comment Share on other sites More sharing options...
gaia.plateau Posted November 26, 2007 Share Posted November 26, 2007 QUOTE (Scalliwag @ Nov 25 2007, 11:22 PM) <{POST_SNAPBACK}>they are less than two bucks. I got mine at an Ace hardware. They are about 3" around and have a little grabber in the middle. So you trim the outer and inner to fit. If you trim one just right you could trim off the tits and that would make them easier to clean. I clean my mods by heated them up with my torch and quenching them in cold water so that should work with this as well.Just remember not to use a steel brush or steel wool because iron particles embed in softer metal and convert to iron oxide so you get rusty aluminum or copper believe it or not. Least that's what Shiner says Could you just cut out a circle of window-screen? I have like 324098230948230948234 square feet of window screen that I bought at Home Depot for $5 to use with my 75g party bowl (the holes are really big, and I needed it to keep the shisha from getting sucked down). I'm not sure that the type of screen you're using would work with my glass scalli mod and I'm too mechanically inept to make a copper one. Link to comment Share on other sites More sharing options...
iamscott06 Posted November 26, 2007 Share Posted November 26, 2007 Yea i dont own a copper one so i think im gonna try and make on for the glass mod... should work out the same you think? Link to comment Share on other sites More sharing options...
nicayotte Posted November 26, 2007 Share Posted November 26, 2007 damn to bad i am at school and cannot see the video, will have to check it when i get home tonight Link to comment Share on other sites More sharing options...
Scalliwag Posted November 26, 2007 Author Share Posted November 26, 2007 QUOTE (gaia.plateau @ Nov 26 2007, 09:08 AM) <{POST_SNAPBACK}>QUOTE (Scalliwag @ Nov 25 2007, 11:22 PM) <{POST_SNAPBACK}>they are less than two bucks. I got mine at an Ace hardware. They are about 3" around and have a little grabber in the middle. So you trim the outer and inner to fit. If you trim one just right you could trim off the tits and that would make them easier to clean. I clean my mods by heated them up with my torch and quenching them in cold water so that should work with this as well.Just remember not to use a steel brush or steel wool because iron particles embed in softer metal and convert to iron oxide so you get rusty aluminum or copper believe it or not. Least that's what Shiner says Could you just cut out a circle of window-screen? I have like 324098230948230948234 square feet of window screen that I bought at Home Depot for $5 to use with my 75g party bowl (the holes are really big, and I needed it to keep the shisha from getting sucked down). I'm not sure that the type of screen you're using would work with my glass scalli mod and I'm too mechanically inept to make a copper one.If you did it that way I would put the tits to the outer edge and give more clearance on the hole it the middle so it came close but not quite touch the glass. It just seems like the aluminum touching the glass would not be good. Dunno why, but...As far as aluminum window screen you could always try it. Once the molasses starts trying to go through the small holes though it may make for a hard draw. But ya never know until you try. Window screen is pretty flimsy and the heat is going to add to that as well. Hope for success, accept setbacks and work off of those setbacks to get it right down the road.... or across the sea. That's my motto ARRRR!!! Link to comment Share on other sites More sharing options...
Johnny_D Posted November 26, 2007 Share Posted November 26, 2007 Scalliwag. I love you.You are the big daddy of hookahforum! Bloody bloody bloody BRILLIANT idea.I gotta swing past Texas to get some shiner, steak and shisha with the legend that is Scalliwag!JD Link to comment Share on other sites More sharing options...
Scalliwag Posted November 26, 2007 Author Share Posted November 26, 2007 QUOTE (Johnny_D @ Nov 26 2007, 03:46 PM) <{POST_SNAPBACK}>Scalliwag. I love you.You are the big daddy of hookahforum! Bloody bloody bloody BRILLIANT idea.I gotta swing past Texas to get some shiner, steak and shisha with the legend that is Scalliwag!JDwell JD if you start swimming west you should be here in about 6 months Good to see you are still around old man. How are things on the other side of the pond? SOS here If you ever did get here you better wear your party cap because the brew will flow, the pipes will smoke, and at least we can look at the local vixens Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now